Weaving Supplies for the Weaving enthusiast



Information

Here you will find various general - not loom specific accessories

Warping Mill

The vertical warping mill is collapsible. With a circumference of 220 cm and tube height of 1 meter, you can put a warp of about 20 meters (22 yd) on it. 

In 2024 we have improved the scheermolen by adding 2 ball bearing rings. It now runs smoother and easier and it is heavier which improves stability.

Product number: WA0188

New and improved warping mill

Warping Posts

Includes table clamp

Product Numbers:
WA0189: warping posts– lacquered beech
WA0301: warping posts – unfinished


Bobbin Rack

Used in sectional warping, our bobbin rack can hold 32 bobbins. Rack includes bobbins.

Product number: WA0190 

Bobbin for bobbin rack

Product number: WA0191  

Warp Tension Regulator

 Louët’s warp tension regulator clamps onto the back beam of any Louët loom. Adjustable tension controls allow for good warp tension, regardless of yarn elasticity or texture. There is an optional counter available in metric or imperial measurement.

Product number: WA0192  

Counter for warp tension regulator

Optional counter for the Louet warp tension regulator available in imperial or metric measurement.

Product number: WA0193   metric

Product Number: WA0194   In

Stick shuttle

These are basic shuttles to be used in weaving.

Product Numbers:
WA0306 – Stick shuttle 30 cm
WA0196 – Stick shuttle 40 cm
WA0307 – Stick shuttle 50 cm
WA0197 – Stick shuttle 70 cm

Flying Dutchman Shuttle

Louët’s unique boat shuttle. Both pins and plastic bobbins will fit on this shuttle The bow in the front allows for a better angle for yarn to unwind from your pin or bobbin. The bow on top spreads any sticky warp threads as you throw your shuttle.

Product number: WA0201 original

 Product number: WA0429 mini

Fly shuttle 40 cm incl. 5 pirns

The fly shuttle fits the fly shuttle device of the Spring, Delta, Octado and Megado looms. It comes with 5 plastic  pirns . Additional pirns can be ordered separately.

Product Number: WA0202

2nd warpbeam 
Kombo

The 2nd warpbeam and back beam is delivered with mounting blocks, apron bars, cords, lease sticks, and warp sticks. It can be assembled in the floor stand or in the back of the castle.

Product number:
WA0101 – 2nd warpbeam Klik/Kombo 40
WA0102 – 2nd warp beam  Kombo 70


Bench Klik/Jane/David/Spring/MD

This bench is designed for the Klik, Kombo and Jane table looms as well as for the David, Spring and Magic Dobby looms. The bench is 57 cm high and stands on rubber buffers. The seating surface of 60 x 25 cm is rounded at the front and rear.

Product number: WA0103


Floorstand Jane/Klik/Kombo

A table loom is useful because you can fold and store it after use. If the loom is permanently set up or if you have little table space, you will benefit from this floorstand. The floorstand also ensures a good working height: the underside of the loom is 67 cm from the floor. You can move the cloth and warp beams to the floorstand, so that they have more capacity.

Product number:
WA0104 - Jane/Klik/Kombo 40
WA0351 – Jane 50
WA0107 – Jane/Kombo 70

2nd warpbeam Jane

The 2nd warpbeam and back beam is delivered with mounting blocks, apron bars, cords, lease sticks, and warp sticks. It can be assembled in the floor stand or in the back of the castle.

Product number::
WA0105 – Tweede scheerboom Jane 40
WA0352 – Tweede scheerboom Jane 50
WA0108 – Tweede scheerboom Jane 70

Carry bag Jane 40

Product number: WA0106

Sectional Kit David l/ll

The sectional for the David comes with 3 slats and plenty of metal brackets. You mount the slats on the existing warp beam. The metal brackets of the 2 cm (or inch) sections are removable, so you can also work with wider sections.

Product number::
WA0110:  David I & 2 70 – 2 cm
WA0111:   David I & 2 70 – inch
WA0113:  David I & 2 90 – 2 cm
WA0114:  David I & 2 90 – inch


Tension Brake David/Spring

Product number: WA0115

Spring l extension to 4 shafts

Today, the Spring comes standard with 8 or 12 shafts. With this extension of 4 shafts and 4 treadles, you can turn a 4 or 8-shaft Spring into an 8 or 12-shaft loom. Older 4-shaft looms can be converted to an 8-shaft or 12-shaft loom with 1 or 2 of these sets. There will be no

Product number::
WA0118:  90 – 4 shafts
WA0122: 110 – 4 shafts

 

David 1/2 90 2nd warpbeam

Product number: WA0112 

Sliding beater kit David 2

Product number:
WA0116 = David 70 l & ll
WA0117= David 90 l & ll

2nd warp beam Spring l


Product number: WA0119 = Spring 90 l 

Sectional for Spring l

The sectional warp for the Spring I comes with 3 section slats and plenty of metal brackets. You mount the section slats on an existing warp beam. The brackets of the 2 cm (or inch) sections are removable, so you can also work with wider sections.

Product number::
WA0120: Spring 1 90 – 2 cm
WA0121:  Spring 1 90 – inch
WA0124: Spring 1 110 – 2 cm
WA0125:  Spring 1 110 – inch

Fly shuttle
 Spring l


Product number: WA0126

Extension set Delta - 4 shafts

With this extension of 4 shafts and 4 treadles you can turn an old 8-shaft Delta into a 12-shaft loom. The extension set does not include heddles; So you will have to order these separately.


Product number:
WA0127: Delta 110 – 4 shafts
WA0131:  Delta 130 – 4 shafts

 

2nd warpbeam Delta

This second warpbeam, complete with cords, 2nd back beam, apron bar, and warpsticks, is mounted in the rear part of the Delta. The second back beam has blocks for attaching to the main back beam; It's easy to slide on and off.

Product number::
WA0128: 2nd warpbeam  Delta 110
WA0132: 2nd warpbeam Delta 130

Sectional Delta / Octado / Megado / Spring II / David III

The sectional warp slats for these looms are the same. The set consists of 4 section slats and sufficient metal brackets. You mount the section slats on an existing warp beam. The brackets of the 2 cm (or inch) sections are removable, so you can also work with wider sections.

Product number::
WA0287–Megado 40– 2cm
WA0288 –Megado 40–inch
WA0401 –David 3/ Octado/Megado 70 – 2 cm
WA0402 –David 3/ Octado/Megado 70 – inch
WA0404 –David 3 / Spring 2 / Octado/Megado 90 – 2 cm
WA0405 –David 3 / Spring 2 Octado/Megado 90 – inch
WA0407-David 3 / Spring 2 Delta /Octado/Megado 110–2 cm
WA0408 –David 3 / Spring 2 Delta/Octado/Megado 110 – inch
WA0133 – Delta/Megado 130 – 2 cm
WA0134 –  Delta/Megado 130 – inch

Treadles Delta per pair 

Product number: WA0135

Treadle height adjusting set Delta

The height adjusting set consists of blocks that you screw onto the treadles and a rail for the foot rest. You raise the treadles and foot rest by 32 mm, so they are at an optimal working height.

Product number: WA0136

 

Fly shuttle device Delta/Megado

Product number: WA0137 

Bench Delta/
Megado

The bench for the Delta/Megado is adjustable in height from 58.5 to 73 cm. The seat is 85 cm wide and 23 cm deep. The accessory tilt set allows you to angle the seat for even more ease of seating.

Product number: WA0138

 

Tilting set bench Delta/Octado/
Megado

The bench tilting set makes it possible to fix the seat of the bench of the Octado, Delta and Megado in an inclined position. You mount the blocks between the legs and the seat, after which you tighten the seat to the desired angle.

Product number: WA0139 

2nd warp beam MD /Kombo 

Product number:
WA0140 = 40 cm
WA0142= 70 cm

Standing beater Magic Dobby 

This upright beater hinges at the base and can therefore not be used if the loom is used as a table loom and the base is not mounted on the floorstand.

Product number:
WA0141 – Standing beater  Magic Dobby 40
WA0143 – Standing beater Magic Dobby 70

Program bars

All program bars are supplied per 10.

Product number:
WA0144 = Magic dobby 
WA0161 = Octado
WA0177 = Megado 16 
WA0178 = Megado 32 

Dobby weight Magic Dobby

With this weight, hanging in the chain of dobby slats, you keep that chain tight. This is helpful  when the chain is too long to keep taut with the tensioners on the loom. When the chain is so long that it hangs halfway to the floor, the weight is not necessary; The weight of the program bars themselves is then sufficient to keep the chain taut.

Product number: WA0145


Mechanical
dobby Magic Dobby

A dobby is a programmable shaft selector. It is the solution to the problem when the space for treadles on a loom is limited. In addition, weaving with a dobby is much more comfortable. Stop working on your knees and tieing up treadles - with a dobby, you can enjoy the pleasure of weaving longer.

With the mechanical dobby you program the pattern, as is done when tying treadles. The program bars are provided with numbered holes, which correspond to the shaft number. By inserting pegs into those holes, you determine which shafts are selected. With a treadle you can move the program bars forward or backward. The mechanical dobby comes with 30 program bars and 600 black pegs.

 Product number: WA0146 

Electronic 
interface Magic dobby

is a programmable shaft selector.  It is the solution to the problem when the space for treadles on a loom is limited. In addition, weaving with a dobby is much more comfortable. Stop working on your knees and tieing up treadles - with a dobby, you can enjoy the pleasure of weaving longer.

The electronic interface is controlled by a computer. The number of pattern picks no longer limits your  pattern. With software from Fiberworks PCW, Patternland, Weavemaker, Weave It, WeavePoint, Winweef or Pro Weave you can design all possible patterns and these programs have a driver that controls the Louët interface.

Product number: WA0147


Raddle Magic Dobby

Product number:
WA0148: Raddle Magic Dobby 40
WA0149: Raddle Magic Dobby 70

2nd warpbeam
Octado 

This 2nd warpbeam, complete with cords, back beam, apron bar and warp sticks, can be mounted in the rear part of the loom. The second back beam has blocks for attaching to the nain back beam; It's easy to slide on and off.

Please note that the image shows a direct warp attached to the second warp beam. This is an accessory that can be ordered separately.

Product number:
WA0150 – 2nd warpbeam Octado 70
WA0153 – warpbeam Octado 90
WA0156 – warpbeam Octado 110

Bench Octado

The bench for the Octado is adjustable in height from 58.5 to 73 cm. The seat is 85 cm wide and 23 cm deep. The separately ordered tilting set allows you to angle the seat for even more ease of seating.

Product number: WA0159


Fly shuttle device Octado/ Spring ll/ David lll

Product number: WA0160

Mechanical 
dobby Octado

With the mechanical dobby you program the pattern, with program bars provided with numbered holes, which correspond to the shafts. By inserting pegs into those holes, you determine which shafts are pulled up. With a treadle you can move the dobby bars forward or backward. The mechanical dobby comes with 20 program bars and 100 black pegs.

Product number:
WA0162 – Mechanical dobby Octado 70
WA0163 – Mechanical dobby Octado 90
WA0164 – Mechanical dobby Octado 110

Electronic interface Octado 

The electronic interface is controlled by a computer. The number of pattern picks no longer limits your  pattern. With software from Fiberworks PCW, Patternland, Weavemaker, Weave It, WeavePoint, Winweef or Pro Weave you can design all possible patterns and these programs have a driver that controls the Louët interface.

Product number: WA0165


2nd warpbeam 
Megado

This second warpbeam, complete with cords,backbeam, apron bar, warpsticks, is mounted in the rear part of the Megado. The second back beam has blocks for attaching to the main back beam; It's easy to slide on and off.

Product number:
WA0286 – 2nd warpbeam  Megado 40
WA0166 – 2nd warpbeam Megado 70
WA0289 – 2nd warpbeam Megado 90
WA0169 – 2nd warpbeam Megado 110
WA0172 – 2nd warpbeam Megado 130


Treadle height adjusting 
Megado

The treadle for lifting shafts is mounted at three heights. If the highest setting is insufficient, the treadle can be raised another 32 or 52 mm with this set.

Product number: WA0175


Mechanical dobby Megado 16 shafts

With the mechanical dobby you program the pattern, with program bars provided with numbered holes, which correspond to the shafts. By inserting pegs into those holes, you determine which shafts are pulled up. With a treadle you can move the dobby bars forward or backward. The mechanical dobby comes with 60 program bars and 660/1200 black pegs.

Product number:
WA0292: 40-16 shafts
WA0179 : 70-16 shafts
WA0293: 90-16 shafts
WA0180: 110-16 shafts
WA0181: 130-16 shafts

Mechanical dobby Megado 32 shafts

With the mechanical dobby you program the pattern, with program bars provided with numbered holes, which correspond to the shafts. By inserting pegs into those holes, you determine which shafts are pulled up. With a treadle you can move the dobby bars forward or backward. The mechanical dobby comes with 60 program bars and 660/1200 black pegs.

Product number:
WA0294: Mechanische dobby 40-32
WA0182: Mechanische dobby 70-32
WA0295: Mechanische dobby 90-32
WA0183: Mechanische dobby 110-32
WA0184: Mechanische dobby 130-32

reed hook/ heddle hook Texsolv (pk 3)

Product number:
WA0187 reed hook red 

WA0208 reed hook white

WA0209 stainless steel reed hook RVS 

warping cards

Product number: WA0195

Flying Dutchman shuttle

Louet’s unique boat shuttle. Both spools and plastic bobbins will fit on this shuttle. The bow in the front allows for a better angle for yarn to unwind from your spool or bobbin. The bow on top spreads any sticky warp threads as you throw your shuttle

Product number:
WA0201 – FD shuttle
WA0429 – FD shuttle mini 

Rag Shuttle 50 cm

With this shuttleyou can easily bring bulky yarn into the fabric.

Product number: WA0200

 


pirns for fly shuttle

These pirns fit on the fly shuttle.

Product number: WA0203


Hand Bobbin Winder

With the hand bobbin winder you can easily wind the yarn on cardboard or plastic spools.

Product number: WA0204


cardboard spools

Product number:
WA0205 – cardboard spool 13 cm – per 10
WA0206 – cardboard spool  15 cm – per 10

Heddle hook

Product number: WA0207